Skip to main content

First-time installation and quick start

WD-15EFirmware: WD-15E mount build; AHC 1.1.0 interface reference

Follow this sequence for a first session in GEM mode. Plan the first powered test where you can see the entire telescope and support. Chapter 03 gives the full mechanical procedure; Chapter 04 explains the electrically different USB-C ports.

In this chapter

2.1 Before you begin​

Prepare a stable tripod or pier, an adapter matching the WD-15E base, the telescope's Vixen or Losmandy dovetail, a suitable 20 V / 5 A USB-C PD source and rated input cable, the supplied AHC cable, and any needed counterweight shaft and weights. A compatible approved 12–24 V DC-to-USB-C input route may be used as specified in 4.3; do not confuse it with the supplied PD-to-12 V DC accessory-output cable.

  1. Confirm the model label says WD-15E. Inspect the mount, saddle clamps, cables and power source for damage.
  2. Choose firm, level ground and identify the full telescope/counterweight travel and all pinch points.
  3. Assess the complete optical payload and the support's stability. The official rating is 8 kg without counterweights, or 13 kg with counterweights at a 20 cm RA arm; see 3.5.
  4. Identify AHC STOP and plan how to support the optical load if input power is lost. The WD-15E has no mechanical RA brake.
WARNING · A free-standing head can tip

Do not command powered movement while the mount is resting loose on a table or support plate. Its center of gravity changes with the latitude setting and axis rotation. Fasten it to a stable tripod or pier first.

2.2 Install the mount and telescope​

  1. Fully deploy and secure the tripod, or check pier anchoring, adapter rigidity and level.
  2. Support the mount while attaching it through the WD-15E-specific base interface. The official drawing identifies 3/8-inch and M6 mounting features. Choose fasteners for the actual adapter and permitted screw engagement; do not force a screw that bottoms out or jams. Tighten all required attachment points and check for rocking.
  3. With the telescope off, choose the coarse latitude position for the observing site, then secure its setting before adding load. See 3.6.
  4. If counterweights are needed, install a compatible M12 × 1.75 shaft and secure each weight and its end stop. Do not assume a shaft or weights came in the standard package.
  5. Support the telescope, seat the dovetail fully in the matching saddle profile and tighten all applicable clamps. Verify retention before releasing your support.
WARNING · Falling optical equipment

A partly seated dovetail can fall when the axes turn. Keep a hand on the telescope while checking both clamp contact points; never loosen a clamp with the telescope unsupported.

2.3 Check and adjust the mechanical setup​

Check the camera, guider, focuser and every cable in the payload assessment. Arrange the telescope and counterweights so the RA axis cannot suddenly swing if motor torque is lost. Check tripod tipping with the telescope in representative orientations; small mount mass does not reduce the overturning force created by a long OTA. Route power and data cables with a strain-relieved loop that cannot enter the saddle clamp, an axis joint or the tripod during a meridian flip.

Point the RA axis approximately toward the appropriate celestial pole. Set its elevation near the observing latitude using the WD-15E's three coarse positions and 30° fine range; use the ±8° azimuth adjustment for small horizontal corrections. Do not force a fine adjuster at its travel stop. Mechanical setup and polar alignment give details.

2.4 Connect power and start the mount​

CAUTION · Check the port before inserting USB-C

The mount's USB-C PD input, saddle Port A power output, saddle Port B data connection, front PC connection and HC interface are different circuits. Their shared connector shape does not make them interchangeable. Connect a live source only to the labeled mount input.

  1. Keep the load stable and the power source off or unplugged. With the mount unpowered, attach AHC to the labeled HC interface using the supplied controller cable. Leave the joystick centered.
  2. Use a suitable USB-C PD 3.0 source capable of 20 V / 5 A, with a cable rated for 5 A, or an approved 12–24 V / 5 A DC-to-USB-C input cable and correctly matched DC source. Keep any AC adapter and mains connections dry and protected.
  3. Connect the source to the labeled mount PD input. The WD-15E has no power switch; once a live source is connected and PD negotiation succeeds, the mount starts. Keep hands and equipment clear of the axes. Confirm a normal AHC connection and mount status.
  4. If a plug overheats, sparks, smokes or produces a burning smell, stop and isolate input power from a safe point. Do not retry the same cable.

Leave the saddle accessory disconnected until the mount status has been checked. When the input is live, left saddle Port A may also be live. Before changing its power lead, stop movement, shut down the accessory, make the optical load safe, disconnect the mount input and verify the output is off. 4.9 gives the power budget and connection order.

2.5 Connect the hand controller or control software​

On AHC, wait for the mount icon to turn green and verify live coordinates/status on Dashboard. A lit screen alone does not prove communication.

For a computer, install the driver described in Chapter 04. Use either the labeled front-panel PC route or saddle Port B, with a data-capable USB-C-to-USB-A cable. Port B is data-only; it does not power a mini PC. Connect the mount's PD input first, then the computer data cable, to avoid possible backfeed from computer USB into an unpowered mount. Prefer one controller for motion commands.

CAUTION · AHC-to-PC cable

When connecting AHC itself to a PC, use a fully wired USB-C-to-USB-C cable compliant with USB 3.2. This is distinct from the AHC-to-mount cable and from the WD-15E's mount-PC connection.

2.6 Confirm location, date and time​

  1. In AHC Settings > Location, choose the actual observing site or use the AHC's GPS location after a valid fix; save and apply it to the mount.
  2. In Settings > Date & Time, choose GPS, NTP or manual entry and set the correct time zone. Verify both UTC and local time.
  3. If N.I.N.A., KStars or another client also writes site/time to the mount, choose the synchronization direction deliberately and recheck the mount's values after connection.

GoTo coordinates, meridian limits and Horizon/Overhead limits depend on correct site, time and pointing information. The WD-15E firmware build does not provide an independent mount GPS source; the supplied AHC GPS can provide these values when it has a fix. See 5.2.

2.7 Initial safety configuration​

Open AHC Settings > Safety & Limits. Review EC HA Limit, AEB, Horizon/Overhead and Meridian values. Check physical clearance around the pier or tripod before selecting limits. The mount firmware initializes EC HA Limit enabled and AEB disabled when its safety settings are blank. If AEB is desired, enable it and tune it for the installed load using the supported AHC procedure; AHC Auto Tune requires AHC 1.1.0 or later and compatible mount firmware.

Restart the WD-15E after changing any safety value or enabled state. A saved value in AHC is not proof the active protection has updated. Read it back after restart and re-establish Home, observing data and pointing state before relying on coordinate limits. Chapter 06 explains the limitations of each layer.

2.8 Complete polar alignment and confirm Home​

Use an established polar-alignment routine such as N.I.N.A., StellarMate/Ekos or ASIAIR plate solving. Inspect its required slew and cable route before starting. Adjust the mechanical latitude and azimuth settings, remeasure, and aim for less than 2 arcminutes (2′) error when the equipment and sky conditions permit. Repeat the check in a representative axis position if a heavy OTA shifts the polar axis. See 3.7.

When needed, use AHC Motion > Go Home or the labeled mount Home control, keep the path clear and confirm the actual Home position. Home uses the RA absolute encoder and DEC optical sensor; it is different from software Sync or Park. Do not use Reset Home to disguise an incorrectly positioned mount. See 5.4.

2.9 Start tracking and perform the first GoTo​

  1. Verify the site/time and Home state. Enable Tracking before the first GoTo or manual slew after power-up; the initial movement interlock otherwise prevents travel.
  2. Select a low slew speed, command a short movement in a clear area and check STOP response and cable behavior.
  3. On AHC GoTo, select a suitable target above the configured horizon. Inspect the target altitude and complete physical path, then send GoTo while watching the mount.
  4. Verify the resulting position with an image or eyepiece. If plate solving, confirm the solution and send Sync to the mount. A solved image without Sync does not update pointing coordinates or activate coordinate-dependent protection.
  5. Check tracking, clearance and safety state before beginning unattended imaging.
WARNING · Watch every initial slew

Keep clear of the telescope, saddle, counterweight and tripod pinch points. AEB cannot prevent initial contact. Use STOP for unexpected motion; do not reach into a moving setup.

2.10 Park, shut down and pack away​

The default Park destination is physically the same as Home, but Park and Home are different commands. A Park command depends on the mount's pointing coordinates. Before the first Park of a session, ensure the observing time/site are correct and a verified plate-solve Sync or equivalent alignment has established the coordinate system. If coordinates are uncertain, do not command an unattended Park. See 5.9.

  1. End imaging and guiding. Inspect the expected Park path, then command Park and wait for the stopped state.
  2. Shut down a saddle-powered accessory normally, then unplug the Port B computer data cable while the mount is still powered.
  3. Support any unbalanced load before removing USB-C input power. The WD-15E has no mechanical brake; holding torque disappears when the motor loses power.
  4. Disconnect the mount input, verify the saddle power output is off, then remove accessory leads, telescope and counterweights while supporting each item.
  5. Dry the equipment before packing it into the soft case. For a later session, recheck Home, observing data, safety settings and cable route.